AOSP

This page contains information that tells how to get OP-TEE up and running on HiKey devices (see HiKey 620, HiKey 960) together with AOSP. The build is based on the latest OP-TEE release and updated every quarter together with the regular OP-TEE releases.

Note

We only use and support this static/stable configuration. If you try using it with the latest available AOSP, there is a risk that both OP-TEE and other parts are not working as expected.

Prerequisites

  • You should already be able to build AOSP for Hikey according to the official instructions. Note that the official build is NOT part of the OP-TEE build. It is a separate and non-related build used only to verify and make sure that your system has everything needed to build AOSP without any issues.
  • Distro should have necessary packages installed, and the repo tool should be installed. Note that AOSP is built with Java. Also make sure that the mtools package is installed, which is needed to make the hikey boot image.
  • In addition, you will need the pre-requisites necessary to build optee-os.

After following the AOSP setup instructions, the following additional packages from main Prerequisites page are needed. Please install them.

Build instructions

$ git clone https://github.com/linaro-swg/optee_android_manifest [-b <release_tag>]
# release tags come in the form of X.Y.Z, e.g. 3.8.0
$ cd optee_android_manifest
HiKey620 - LeMaker 8GB
$ ./sync-p.sh
$ ./build-p.sh
HiKey620 - CircuitCo 4GB
$ ./sync-p.sh
$ ./build-p.sh -4g
HiKey960
$ ./sync-p-hikey960.sh
$ ./build-p-hikey960.sh

These steps MUST finish with no errors. For sync*.sh scripts, that means there must be no errors prior to the Sync done! console output. For build*.sh scripts, that means there must be a #### build completed successfully (MM:SS (mm:ss)) #### console output! If there are errors, then there is no point in trying to flash the device.

Warning

  • --force-sync is used which means you might lose your work so save often, save frequent, and save accordingly, especially before running sync-p.sh again!
  • Attention! Do NOT use git clean with -x or -X or -e option in optee_android_manifest/, else risk losing all files in the directory!!!

Hint

You can add the -squashfs option to build.sh option to make system.img size smaller, but this will make /system read-only, so you won’t be able to push files to it.

Currently, only version P is supported. Other existing files are for internal development purposes ONLY and NOT SUPPORTED!

Flashing the image

The instructions for flashing the image can be found in detail under device/linaro/hikey/installer/hikey{960}/README in the tree.

  1. Set jumpers/switches 1-2 and 3-4, and unset 5-6.
  2. Reset the board. After that, invoke:
HiKey620
$ cp -a out/target/product/hikey/*.img device/linaro/hikey/installer/hikey/
$ sudo ./device/linaro/hikey/installer/hikey/flash-all.sh /dev/ttyUSBn
HiKey960
$ cp -a out/target/product/hikey960/*.img device/linaro/hikey/installer/hikey960/
$ sudo ./device/linaro/hikey/installer/hikey960/flash-all.sh /dev/ttyUSBn

where the /dev/ttyUSBn device is the one that appears after rebooting with the 3-4 jumper set. Note that the device only remains in this recovery mode for about 90 seconds. If you take too long to run the flash commands, it will need to be reset again. After flashing, unset the 3-4 jumper again to boot normally.

Partial flashing

The last handful of lines in the flash-all.sh script flash various images. After modifying and rebuilding Android, it is only necessary to flash boot, system, cache, vendor and userdata. If you aren’t modifying the kernel, boot is not necessary, either.

Experimental prebuilts

Available at http://snapshots.linaro.org/android under android-hikey* directories. Note that these images do not always work and are NOT SUPPORTED as well!

Running xtest

Do NOT try to run tee-supplicant as it has already been started automatically as a service! Once booted to the command prompt, xtest can be run immediately from the console or an adb shell. For more details about running OP-TEE, please see Run xtest at optee_test.

Running VTS Gtest unit for Gatekeeper and Keymaster (Optional)

On the device after going into the command prompt, run:

$ su
$ ./data/nativetest64/VtsHalGatekeeperV1_0TargetTest/VtsHalGatekeeperV1_0TargetTest
$ ./data/nativetest64/VtsHalKeymasterV3_0TargetTest/VtsHalKeymasterV3_0TargetTest

Note

These tests need to be run as root.

Enable adb over USB

Boot the device. On serial console:

$ su setprop sys.usb.configfs 1
$ stop adbd
$ start adbd

Known issues

  • If you don’t have a monitor or hdmi emulator (dummy plug) connected to the board, you’ll see constant errors scrolling on the console. As a workaround, move android.hardware.graphics.composer@2.1-service.rc out of /vendor/etc/init. Move it back in when working with a monitor again.
  • Adb over USB currently doesn’t work on HiKey960. As a workaround, use adb over tcpip. See https://bugs.96boards.org/show_bug.cgi?id=502 for details on how to connect. There are still some limitations however. E.g. running adb shell or a second adb instance will break the current adb tcpip connection. This might be due to unstable WiFi (there are periodic error messages like wlcore: WARNING corrupted packet in RX: status: 0x1 len: 76) or just incompleteness of the generic HiKey960 builds under P.